|
| | Goto page :  1, 2, 3, 4, 5 | | Author | Message |
|---|
makitupthehardway
moderator
  
Age : 26
Joined : 19 Jan 2007
Posts : 1244
Localisation : Ashburn, VA
|  Subject: Re: Axle Swap  Mon Nov 05, 2007 5:41 pm | |
| I must say know that its all done you did a great job paul. I went back and read thru this post. I was trying to see pictures of longfeilds and how Toyota axles go together. Thanks for the pictures Paul.
_________________
2008 ADA run - Trail Master (all questions welcome)
94YJ locker/spool, lifted 37" MTR's lots of cool stuff (Trail rig)
00WJ open/open, lifted 31" MTR's (curbcrawler)
84 Toyota Pickup open/welded, 33's solid front axle and rusted frame
07 FORD E350 SD (TOW VAN)
KARNAGE MOTORSPORTS INC.[b] |
|   | | mdcj7
Locker/Spool
 
Age : 54
Joined : 19 Jan 2007
Posts : 248
Localisation : Parkville, Maryland
| | Subject: Re: Axle Swap Mon Nov 05, 2007 6:48 pm | |
| Nester if want want more I can email you all my pictures of the swap.
_________________
81 cj7 258 HEI, MC2100,Clifford header,4WDH 4" lift, 33" tires, T-177, D300, 4:10 gears, aussie locker front and back, Toyota axles, Longfield 30 spline chromoly superaxles, BigDaddy rockers,Mastercraft seats, Full cage
2006 LJ all stock 3:73 gear LS dana 44 rear 4.0 L 6speed trans,Volant CAI, Magnaflow cat back |
| | | | makitupthehardway
moderator
Age : 26
Joined : 19 Jan 2007
Posts : 1244
Localisation : Ashburn, VA
| | Subject: Re: Axle Swap Mon Nov 05, 2007 7:46 pm | |
| thanks Paul I will let you know.
_________________
2008 ADA run - Trail Master (all questions welcome)
94YJ locker/spool, lifted 37" MTR's lots of cool stuff (Trail rig)
00WJ open/open, lifted 31" MTR's (curbcrawler)
84 Toyota Pickup open/welded, 33's solid front axle and rusted frame
07 FORD E350 SD (TOW VAN)
KARNAGE MOTORSPORTS INC.[b] |
| | | | Rockn93YJ
Locker/Spool
 
Age : 40
Joined : 20 Jan 2007
Posts : 1105
Localisation : Knoxville, MD
| | Subject: Re: Axle Swap Tue Nov 06, 2007 8:43 am | |
| | How much lift are those springs? what size tires are you running? I'm trying to figure out what is going to work with my 79 CJ7 but have no clue what fits and what hits. I've seen the charts but they are not helpful in a practical sense. Right now I have a spring over on bronco axles. springs are new but not sure from what vehicle yet. I don't plan on much articulation since it will primarily be a mud vehicle. |
| | | | mdcj7
Locker/Spool
Age : 54
Joined : 19 Jan 2007
Posts : 248
Localisation : Parkville, Maryland
| | Subject: Re: Axle Swap Tue Nov 06, 2007 12:39 pm | |
| Bill I have a BDS 4" lift and 33 with no problems with SOA you should be able to fit 36's with no problem but with full with axle your rear fender should be in the middle of the tire. A good bounce and you will open the fender. RE sell a spring just for SOA on a YJ that can be put on a CJ.
_________________
81 cj7 258 HEI, MC2100,Clifford header,4WDH 4" lift, 33" tires, T-177, D300, 4:10 gears, aussie locker front and back, Toyota axles, Longfield 30 spline chromoly superaxles, BigDaddy rockers,Mastercraft seats, Full cage
2006 LJ all stock 3:73 gear LS dana 44 rear 4.0 L 6speed trans,Volant CAI, Magnaflow cat back |
| | | | Rockn93YJ
Locker/Spool
Age : 40
Joined : 20 Jan 2007
Posts : 1105
Localisation : Knoxville, MD
| | Subject: Re: Axle Swap Tue Nov 06, 2007 6:12 pm | |
| | mdcj7 wrote: | | A good bounce and you will open the fender. RE sell a spring just for SOA on a YJ that can be put on a CJ. |
What do you mean "open the fender"? I picture the tire being crammed up into the narrow wheelwell opening in the body. I'm guessing the full width bronco axles are the same width as the 79 Ford F350 D60 axles. if so then they won't stick out too far and body clearance will be an issue.
36" tires is good since that is what I'll run for now. Plan is to run 36" and under modified stock class in mud races until I have the 454/Turbo400/NP205 built and ready to go. |
| | | | |
| Page 5 of 5 | Goto page : 1, 2, 3, 4, 5 |
| | Permissions of this forum: | You cannot reply to topics in this forum
| | |
| |
|
